|
1-1-predstavlenie-spravochnojj-sistemy.html
1.1. Representation of help systemEveryone the head of this system is always subdivided into following sections: the theory, maintenance service, elimination of malfunctions and repair work.
The theory: here the general information on the technician and functioning is resulted. Besides the detailed description this section includes also the technical terminology concerning considered specific problems.
Maintenance service: here the detailed instruction on all necessary works is step by step given. Additional working badges demonstrate to you necessary expenses of time, difficulty degree, and also possible dangers to safety and environment. Detailed illustrations also visually explain stages of working process and problems arising thus.
Repair work: here too necessary separate working steps, by analogy to the description of works on maintenance service are consistently described.
Practical advice: will help you during carrying out of the specified works and the decision of arising problems. The section concerning repair, includes also more often point – elimination of malfunctions where the list of arising defects, their possible reasons and actions on their elimination is resulted.
The themes concerning to the technics and the list of malfunctions, reveal similarly both in the maintenance review, and in the index.
|
|
|
Engine knots The block of cylinders of the engine. Moving details Here take places. More often it is made of grey pig-iron. On the block of cylinders of the engine the generator, a starter and ignition system take places also.
Head of the block of cylinders. Settles down over cylinders. In it there are channels for pass of a fresh mix and the fulfilled gas, a saddle of valves, bearings and directing for details which operate work of valves, a carving for spark plugs, channels of water delivery and the combustion chamber. |
|
30 000 km or 2 years
|
|
Dismantle the muffler of noise of an admission. In the diesel engine: dismantle an inlet air pipe. In all engines: disconnect electric штекерные connections
Unscrew six screws of a cover of a head of the block of cylinders and cautiously uncover. If the cover sits strongly and is not released, knock on it with a palm of a hand or the hammer handle.
For measurement of inlet and final valves of the separate cylinder it is necessary to release both valves in the beginning. For this purpose turn the engine until on a camshaft the ends of both cams of the cylinder 1 (to the right of a movement direction) at the left and on the right from above will not be symmetric (pay attention to marks top МТ). This position corresponds to the top dead point.
|
|
You carry out working actions step by step, according to spent servicing or repair. Besides, the moments where it is necessary to make corresponding efforts and on are here too marked what it is necessary to pay special attention.
Cooling system
|
The reason
|
Elimination
|
|
A. The arrow of the index of temperature settles down in red sector
|
Weak tension клиноребристого a belt or rupture presence
There is not enough liquid in cooling system
The wire to the temperature indicator has connection on weight
|
To check up a tension of a belt or to replace a belt
To add, as a last resort, to take from system of washing of glasses
To disconnect a wire to the temperature indicator, the index should fall in extreme position, otherwise there is a connection to weight; to check up ought проложение wires
|
|
|
|
Pressure decrease of compressed air If compressed air leaves in one of following places more often the reasons of it can be:
Inlet collector or the case of the air filter: the defective inlet valve.
Open radiator or compensatory tank with cooling means: a defective lining of a head of the block of cylinders.
|
|
It is impossible to be engaged in the self-help during a warranty period
If you go on new Ford Mondeo necessarily observe the intervals of maintenance service established by the manufacturer. First of all refuse any self-help: necessary guarantee certificates should execute only Ford for the corresponding guarantee workshop should regularly and carry out in due time necessary on yours Mondeo preventive works. It first of all concerns replacements of units, such, for example, as the engine or a transmission.
Service of help system:
The list of checks
In given managements are resulted different lists of the necessary checks which carrying out will render yours Mondeo the help both in working everyday life, and during the winter period or will facilitate a campaign in TÜV/DEKRA. Here the necessary checks are resulted.
Working badges
The given badge of a tree should remind you of environment protection. It takes places always in the event that concrete work or "waste" appearing thus can affect environment.
The quantity of wrenches signals you about degree of difficulty of executed work.
1 key = easy work; 2 keys = exacting work; 3 keys = a tough job.
Symbols of a sand-glass give to the fan of a screw-driver representation about average operation time. The estimated time includes absence at you necessary working skills and presence not optimum equipment for work.
The exclamation sign basically is established before such works during which execution the factors influencing working safety of your car can be shown: hands off works with such badge! The given work should be spent ONLY in a workshop.
The control badge classifies preventive works. Among other, it can save to you money and time if you on servicing and check execute the works marked with such badge independently before visiting in target dates TÜV or DEKRA.
The given badge marks each work on the servicing, carried out on yours Ford Mondeo which also can be executed in the large or small service centres Ford, all points correspond to the official plan of servicing Ford.
| 