> Whether coupling is completely separated?. Ford Mondeo (since 2000 of release)
Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
10.1. Coupling
10.2. Coupling check
10.3. Whether coupling is completely separated?
10.4. A five-step mechanical transmission
10.5. Gear change adjustment
10.6. Level check трансмиссионного oils (a mechanical transmission)
10.7. Good alternative to a mechanical transmission – automatic box Mondeo in a combination with 2,0-litre engine Duratec-HE
10.8. Level check трансмиссионного oils (an automatic transmission)
10.9. The main transfer
10.10. Check of cuffs of power shafts
10.11. Dismantle and power shaft installation / the cross-section lever of a suspension bracket
10.12. Replacement of cuffs карданного the hinge
11. A running gear
12. Brake system
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions

ba88fb63 Купить кондитерские Ингредиенты


10.3. Whether coupling is completely separated?

If at switching from the lowest transfers on the higher scratching or roaring noise coupling is separated incorrectly more often are audible. Inspect switching on a backing! However, by means of such check possible defects of a transmission are excluded also.


  1. Start the engine idling.
  2. Completely include coupling and wait further about three seconds before switching on a backing. If you hear the same sounds of a gnash, coupling is divided carelessly.
  3. Before repair carrying out it is necessary in any case in a specialised workshop to inspect system of automatic control of a free wheeling of a pedal of coupling.


Driving with not tight hydraulic system of coupling

In that situation when the hydraulic system of your coupling Mondeo "has on the journey begun to flow" (негерметичны conducting (distributive coupling cylinders, has burst a hose, air in hydraulic system), recollect our three councils.

It is supposed that you show a few patience and the gentle reference with a gas pedal, and also the gear change lever, to "outwit" a transmission of the Mondeo it is possible, of course, and without coupling inclusion.

Трогание from a place without coupling inclusion

Switch off the engine. Establish 1st transfer, then include a starter. You Mondeo moves jerky as soon as the engine was started, give to a few gas. If during movement there is no desire to switch transfer, right after трогания establish 2nd transfer.

Switching on higher transfer without coupling inclusion

Establish strictly 1st transfer after transition to turns above frequency of rotation of idling (about 1000 rpm). Remove a few gas. The gear change lever slightly establish before"2nd transfer. If transfer is clamped, give a few gas, release a pedal of gas and cautiously include the lever 2nd transfer. At synchronous frequencies of rotation of the engine and a transmission transfer slips by itself. If you still wish to wait longer give a few gas, thereby the range of change of the transfer relation without a gnash of cogwheels will come to gearing . If unsuccessfully, once again be late and again try"happiness".

All other transfers include similarly. In the best way it occurs at low speeds: on 3rd transfer at 30 km/h, on 4th at 40 km/h and on 5th at 50 km/h.

Switching on low transfer without coupling inclusion

This process is better occurs at small turns of the engine and speeds.

At first remove a foot from a gas pedal. Cautiously give gas a little to increase engine turns. Simultaneously establish the switching lever before"smaller transfer. At the necessary frequency of rotation of the engine establish this transfer.

On other transfers arrive in the same way.

The previous page
10.2. Coupling check
The following page
10.4. A five-step mechanical transmission