Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
12. Brake system
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
16.1. Dismantle and door installation
16.2. Door adjustment
16.3. Dismantle and installation of an external rear-view mirror
16.4. Dismantle and installation обтекателя
16.5. Dismantle and cowl installation
16.6. Adjustment of a cowl of the engine
16.7. Dismantle and installation of a cover of a bumper (forward)
16.8. Dismantle and installation of wings
16.9. Dismantle and installation of a cover of a bumper (back)
16.10. Dismantle and installation of a cover of a luggage carrier
16.11. Adjustment of a cover of a luggage carrier
16.12. Dismantle and installation of the lock of a back door
17. Technical characteristics
18. The help at malfunctions
 



ba88fb63



16-11-regulirovka-kryshki-bagazhnika.html

16.11. Adjustment of a cover of a luggage carrier

 PERFORMANCE ORDER

    Put the car on an equal surface and open a luggage carrier cover. Unscrew on back trailer sheet all rod screws (are specified by arrows).

    Unscrew all rod screws (arrows) on back trailer sheet.

    Remove the left top lining of a cover (it is specified by an arrow) and …

    Remove a cover lining.

    … unscrew two buffers on the back end of a cover of a luggage carrier. Dismantle now rotary демпфер covers of a luggage carrier and … … level a cover loop to coaxially screws (arrow) on a lateral detail. Ослабьте screws so that there was a possibility of displacement of a cover.

    Level a cover loop to coaxially screws (are specified by arrows) on a lateral detail.

    Ослабьте screws on a luggage carrier cover so that there was a possibility of displacement of a cover. Close a cover and establish behind распорный an element (it is specified by an arrow) in the thickness of 4 mm between lateral edge of a cover of a luggage carrier and a lateral wall.

    Insert распорный an element (it is specified by an arrow) in the thickness of 4 mm between lateral edge of a cover of a luggage carrier and a lateral wall.

    As soon as the cover will be levelled on a backlash, remove распорный an element and cautiously lift a cover. Now it should not move in loops. Tighten now шарнирные screws the moment of an inhaling 23 Н·м and … … ослабьте then loopy screws (are specified by arrows) on a body so that there was a possibility of moving of a cover with effort.

    Ослабьте slightly loopy screws (are specified by arrows) on a body.

    Close a cover and press it downwards in zones of loops so that it had a backlash from lateral walls at a rate of 2 mm.

    Create a backlash at a rate of 2 millimetres.

    Cautiously open a cover – loops should not slip – tighten fixing screws the moment 23 Н·м. Screw both back buffers so that the closed cover of a luggage carrier slightly adjoined. Instal upside-down.

 PRACTICAL ADVICE

Dismantle of a back door

That it is more convenient to attach "interiors" of a back door, already during dismantle all disconnected contacts "are extended" by means of a cord. Wires are pulled out from a door then from other end together with already tied up cords. Cords can "dangle" long enough from both parties as to them for installation I will fasten new details. Installation is carried out upside-down – thus cords are used in a role of "pathfinder" for wires and hoses.

Replacement of a rubber sealant

    If the back door is already removed, at once check up also it уплотнители: not tight places "give out" themselves traces of a dust or drains of water from both parties of condensing surfaces. If the sealant became fragile or has become covered by cracks, offer to the Mondeo a new shaped detail. For this purpose remove an old sealant and clean folds from the rests of a former lining and pollution. Squeeze out a little new condensing means (for example, means for consolidation of seams, silicone) in a special flute. If you near at hand do not have ready shaped detail establish a sealant in the middle of the lock and then press it along the edges. The acting ends properly cut off lateral обрезателем. Give to this connection end-to-end a few tension and then cautiously beat a rubber hammer on a fold.

«The previous page
16.10. Dismantle and installation of a cover of a luggage carrier
The following page»
16.12. Dismantle and installation of the lock of a back door