> Coupling. Ford Mondeo (since 2000 of release)
Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
12. Brake system
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions
18.1. A starter
18.2. The accumulator and the generator
18.3. System of injection of gasoline
18.4. Brakes
18.5. Injection system - a diesel engine
18.6. Electric стеклоподъемник
18.7. A heating system
18.8. Cooling system
18.9. Coupling
18.10. The engine and system
18.11. Braking signals
18.12. A screen wiper
18.13. Greasing system
18.14. The thermostat
18.15. System of the sound and light alarm system
18.16. Screen wiper brushes
18.17. System of locks with the central management
18.18. Spark plugs
18.19. A lining of a head of the block of cylinders
 






ba88fb63 На http://www.obzorotelei.ru обзоры отелей.

18-9-sceplenie.html

18.9. Coupling

The reason
Elimination
A.Stseplenie revolves.
  1. Adjusting automatics is defective; initial pressure in system (1 bar) too high (the valve of primary pressure is clamped).
  2. Coupling linings are worn out.
  3. The clamping effort of coupling is not enough.
  4. The coupling lining is made oily.
  5. Coupling was перегрето.
  1. If necessary replace the main conducted cylinder of coupling with the bearing of deenergizing of coupling, replace the valve of initial pressure.
  2. Replace a conducted disk.
  3. Replace press a coupling disk. A conducted disk at once replace together with it.
  4. Sealing ring of radial shaft on a cranked shaft or an entrance shaft of a transmission негерметично. Replace the worn out ring.
  5. Check up an engine flywheel, if necessary grind, completely replace coupling.
B.Stseplenie is not divided.
  1. Look А1.
  2. The conducted or leading cylinder of coupling the defective.
  3. Air in hydraulic system.
  4. The conducted disk is clamped on a transmission shaft.
  5. The conducted disk is broken.
  6. Conducted disk the lining is warped or broken.
  7. Lining after long standing приржавела to a flywheel.
  1. Replace defective cylinders.
  2. Add a liquid; ventilate coupling.
  3. Thoroughly clean and slightly grease шлицевое connection.
  4. Replace a conducted disk.
  5. Get under way from a place as it is described in section Driving without coupling inclusion. Constantly hold a pedal of coupling of the pressed. Sharply press on a pedal of gas and then release, that coupling has broken.
  6. Defective details replace.
V.Stseplenie is not divided and revolves simultaneously.
Automatic drive of coupling the defective. Replace.  
G.Stseplenie pulls.
  1. Look А3.
  2. The engine or transmission suspension bracket it is weakened or defective.
  3. Firm zones (roughnesses on a flywheel or a press disk).
  4. Wrong linings (hardness degree). Гаситель крутильных fluctuations it is worn out.
  1. Fix or replace an engine mount or transmissions.
  2. Further it is necessary to replace a flywheel, press a disk replace at once.
  3. Replace a conducted disk.
D.Shumy in coupling.
  1. Disbalance of a press disk of coupling or conducted disk.
  2. The spring гасителя крутильных fluctuations is worn out.
  3. The bearing of deenergizing of coupling the defective.
  4. Connecting elements in an automatic drive of coupling are worn out broken).
  1. Replace defective details.
  2. Replace a conducted disk.
  3. Replace the central distributive cylinder with the built in bearing of deenergizing of coupling.
  4. Replace an automatic drive of coupling.

The previous page
18.8. Cooling system
The following page
18.10. The engine and system