|
12-13-zamena-kolodok-diskovogo-tormoznogo-mekhanizma.html
12.13. Replacement колодок the disk brake mechanismReplacement of overlays basically is made only in pairs from both sides of the bridge. Otherwise on brake disks there will be different factors of a friction which subsequently about full braking «confidently will throw out» your car from a track. Owing to thermal influence new brake колодки to the first 500 km change the material structure: allow to these segments time to "come to the senses" and do not apply at the beginning whenever possible full braking. Otherwise колодки can quickly harden (to "glaze over") and subsequently more never to restore the usual factor of a friction. Besides pedantically pay attention that spare details of brakes had the permission of the manufacturer and ought to Ava for yours Mondeo. If you are tormented with doubts show "fig" towards doubtful counters with the goods is better and "refuel" original spare parts at the dealer Ford.
The forward disk brake mechanism in details
The forward bridge
|
|
Lift a forward part of the car on goats and remove wheels.
Dismantle a brake hose from the holder and...
... Remove an external fixing spring.
Before демонтажем a support of the brake mechanism wring out it slightly outside, the brake piston receives a small backlash.
Dismantle a support from two fixing screws 2, preliminary having removed at screws caps 1 by means of a screw-driver.
|
|
Fixing screws of a support of the disk wheel brake mechanism. |
To disconnect a brake hose, suspend a support by means of a welded wire in a wheel niche.
Pull out external brake колодку through keeping ledge of a clamping spring and...
... Dismantle it from a support.
Then dismantle internal brake колодку.
Before inserting into a grip new brake elements, wring out back brake pistons by means of the special tool «Ford 206-005 (12-014)» or a suitable screw-driver. Attention: thus liquid level in a compensatory tank of the main brake cylinder raises. At once смойте water a following liquid.
Adhere brake disks before establishing a support, slightly wipe its emery paper.
Insert into a support at first internal, and then external колодку. Preliminary grease contact surfaces with a thin layer heat resisting copper paste.
Pull a clamping spring for keeping ledge and...
... Move after that a support on a disk and fix it.
Instal upside-down.
Pump over a brake pedal until brake pressure will be created. Only after that put overlays on brake disks.
Check up now level of a brake liquid in a compensatory tank. Surplus of a liquid can be sucked away by means of a pipette or a syringe to a label «MAX».
Brake with new колодками cautiously. For example, on country roads where some times it is necessary to brake about nearby 100 km/h to 50 km/h. From time to time give the chance колодкам to be cooled.
|
|
The back bridge
|
|
Lift on an emphasis a back part of the car, reliably fix and remove wheels.
Lower a cable of a lay brake. For this purpose press the lever 1 to a brake support from within and lower a cable 2.
|
|
Свешивание a cable 2 lay brakes; 1 lever on a cable. |
Unscrew on a brake support the bottom fixing screw (it is specified by an arrow).
|
|
In the beginning unscrew the bottom fixing screw (it is specified by an arrow) on a brake support. |
To establish the piston in a brake support, strong keep a support. Press the piston in a direction of a support and turn a key with internal шестигранником (it is specified by an arrow), in model with a body the versatile person in a direction of a back door, in a sedan and a compartment in a direction of a cowl of the engine. «Проникшая» in a support the brake liquid comes back back in a compensatory tank. If necessary suck away a superfluous liquid from a tank.
|
|
Insert the piston into a brake support by means of a key with internal шестигранником. |
Turn a support upwards and pull out old колодки (are specified by arrows) from corresponding mines.
|
|
Pull out колодки (are specified by arrows) from mines of brake overlays. |
Before installation of new segments grease contact surfaces with heat resisting copper paste, level flutes in a brake support and...
... Screw the bottom screw in a support.
|
|
Flute alignment in a brake support. |
Suspend a cable of a manual brake on a support and then connect to the lever. For this purpose press the lever 1 from within and suspend a cable 2 on the lever.
|
|
Suspend a cable of a manual brake on a support: in the beginning press the lever 1 from within and only then suspend a cable 2. |
Establish wheels, "pump over" a pedal of a brake with effort and then some times pull a manual brake. Check up level of a brake liquid in a compensatory tank and if necessary add to a mark «MAX».
Finish work upside-down and check up braking new колодок as it is described above.
|
|
|
|
