> Replacement of disks of the brake mechanism. Ford Mondeo (since 2000 of release)
Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
12. Brake system
12.1. Check of level of a brake liquid
12.2. Check of brake system
12.3. Check of the amplifier of a brake drive
12.4. Check of brakes on functioning
12.5. Deterioration measurement колодок the disk brake mechanism
12.6. Check износадискового the brake mechanism
12.7. Prorolling of brake system
12.8. Replacement of a brake liquid
12.9. Dismantle of a compensatory tank of the main brake cylinder
12.10. Dismantle and installation of the main brake cylinder
12.11. Dismantle and installation of the amplifier of a brake drive
12.12. Dismantle and installation of brake hoses
12.13. Replacement колодок the disk brake mechanism
12.14. Replacement of disks of the brake mechanism
12.15. To make suitable a support and the piston of the brake mechanism – replacement of protective cuffs
12.16. A lay brake
12.17. Replacement of a cable of a lay brake
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions
 






ba88fb63

12-14-zamena-diskov-tormoznogo-mekhanizma.html

12.14. Replacement of disks of the brake mechanism

Replacement of disks basically is made only in pairs, otherwise on brake disks there will be different factors of a friction – brakes can pull in this case aside.

The forward bridge

 PERFORMANCE ORDER

  1. Spend in the beginning actions, as at replacement brake колодок and...
  2. ... Block a support by means of a welding wire in a wheel niche.
  3. Remove safety скобы a disk from wheel bolts. If necessary during installation replace rusted скобы.
  4. Mark oil small of an emergency set position of a disk in a nave of a wheel and...
  5. ... Then cautiously shift a disk by means of a rubber hammer from a wheel nave.
  6. Before disk installation thoroughly clean a wire brush adjoining surfaces of a wheel nave and a disk that the disk strictly adjoined.
  7. Establish a disk – according to marks – on a nave and...
  8. ... Displace safety скобы on wheel bolts.

    The forward disk wheel brake mechanism in details:

    1 — the Nave of a wheel,
    2 — the Disk of the brake mechanism,
    3 — the Safety washer,
    4 — the Brake holder,
    5 — the Support of the brake mechanism,
    6 — Brake колодки.

  9. Then fix a brake support on a rotary support of the steering mechanism and finish installation upside-down.

The back bridge

 PERFORMANCE ORDER

  1. Operate in the beginning, as at replacement brake колодки and...
  2. ... Fix a brake support by means of a welded wire in a wheel niche.
  3. Remove safety скобы a disk from wheel bolts. If necessary during installation replace rusted скобы.
  4. Mark oil small of an emergency set position of a disk in a nave of a wheel and...
  5. ... Then cautiously shift a disk by means of a rubber hammer from a wheel nave.
  6. Before disk installation thoroughly clean a wire brush adjoining surfaces of a wheel nave and a disk that it densely adjoined.
  7. Establish a disk – according to marks – on a nave and...
  8. ... Displace safety скобы on wheel bolts.
  9. Fix then a support on a semiaxis and finish installation upside-down.

The previous page
12.13. Replacement колодок the disk brake mechanism
The following page
12.15. To make suitable a support and the piston of the brake mechanism – replacement of protective cuffs