Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
12. Brake system
13. The electrotechnical equipment
13.1. The storage battery and a starter
13.2. The generator
13.3. Check of level of electrolit in the accumulator
13.4. Care of contacts
13.5. Check of the storage battery
13.6. Engine start "from outside" – with a wire connecting a starter and the auxiliary storage battery, without problems
13.7. Car pushing
13.8. Car towage
13.9. Gymnastics of the storage battery
13.10. Replacement of the storage battery
13.11. Revealing of secret consumers of the electric power
13.12. Check of a regulator of pressure
13.13. Replacement приводных belts
13.14. Replacement of a belt clamping roller
13.15. Dismantle and generator installation
13.16. Starter replacement
13.17. External illumination
13.18. Any big problems – replacement of lamps накаливания
13.19. A provisional measure – adjustment of headlights «before a wall»
13.20. Signalling devices
13.21. Check of the switch of a signal of braking
13.22. Check of a sound signal
13.23. Tools and actuation devices
13.24. Check of functioning of the switch
13.25. Dismantle and installation of the combined device
13.26. Not always simply to follow – "twisting" roads of wires
13.27. Protection against overloads – safety locks in salon and a motor compartment
13.28. It is carried out quickly – replacement of safety locks
13.29. Distributes strong working currents – the switching relay
13.30. An apportion of safety locks and the relay
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions
 



ba88fb63



13-13-zamena-privodnykh-remnejj.html

13.13. Replacement приводных belts

In engines Mondeo automatic ременный натяжитель supports поликлиновые belts in a tension condition. Thus, it is possible not to worry about a tension of belts any more. However clamping rollers should be examined from time to time. If thus you do not notice in «a rest condition» anything unusual start the engine and pay attention to movement of a clamping roller: if you include "heavy user", for example, the conditioner, heating of back glass, etc., the serviceable roller "is slightly shaken" – however, even then, when «the gas push» is given the engine strong. Strong deterioration of belts (non-uniformly deep furrows) continuously induces clamping a roller to oscillative motions. For elimination of these lacks in the beginning it is necessary to replace приводной a belt. Track that the new belt had the same specification, as former.

The given work on engine Duratec-HE example is more low described.

 PERFORMANCE ORDER

    Establish a manual brake and reliably raise a jack a forward part of the car. Dismantle a forward protective wall приводного a belt. Ослабьте a roller 7 and... ... Remove the worn out belt. Check up all belt pulleys on deterioration and faultless rotation. Lay a new belt in pulleys and strongly tighten tightening the screw on a clamping roller (nearby 5–6 Н·м).

    Twisting roads: приводной a belt in engine Duratec-HE.

    1 — the Generator,
    2 — the Rotary roller,
    3 — the Pump of the steering mechanism with the amplifier,
    4 — the Water pump,
    5 — the Expert-compressor,
    6 — Gasitel крутильных fluctuations of a cranked shaft,
    7 — Automatic ременный натяжитель.

    Updating: ременный a drive "new" Duratec-VE.

    1 — the Generator,
    2 — the Pump of the steering mechanism with the amplifier,
    3 — Automatic ременный натяжитель
    4 — the Expert-compressor,
    5 — Gasitel крутильных fluctuations of a cranked shaft.

    With two rotary rollers: ременный drive DuraTorg-DI.

    1 — the Rotary roller,
    2 — Remennyj натяжитель,
    3 — the Rotary roller,
    4 — the Expert-compressor,
    5 — Privodnoj a belt,
    6-Gasitel крутильных fluctuations of a cranked shaft,
    7 — the Generator.

    The pump of the steering mechanism resulted by a camshaft with the amplifier.

    1 — Remennyj натяжитель,
    2 — the Camshaft,
    3-Privodnoj a belt,
    4 — the Pump of the steering mechanism with the amplifier.


«The previous page
13.12. Check of a regulator of pressure
The following page»
13.14. Replacement of a belt clamping roller