13.18. Any big problems – replacement of lamps накаливания

Rotate a lamp cartridge to the left and completely unscrew together with a lamp from the case. Slightly compress an old bulb in a cartridge and unscrew its left rotation. Establish a new lamp upside-down and track that at installation both directing ledges correctly settled down.


Вывинчивание the left rotation: at first a cartridge, then a lamp.

Cautiously shift glass of the index of turn from a wing so that the spring under a tip could be wrung out a screw-driver and completely to pull out glass from a wing.



Pay attention to a back spring at installation of the lateral index of turn.

Strongly keep a lamp cartridge, rotate glass to the left and remove. Pull out a lamp from a cartridge and replace with the new. Instal upside-down.

Open the headlight case. For this purpose at first disconnect the lamp tip, release tightening shutters and put aside caps.



Observe an order: disconnect the lamp tip, and then release tightening shutters.

Disconnect the lamp tip (it is specified by an arrow), cast away in the parties wire скобы (are specified by arrows) and pull out a lamp for a socle from a reflector. Insert a new lamp, connect it and then close a headlight. Track that wire shutters have risen on the places.



Galogennaja lamp: always to take only for a cartridge.

Disconnect the lamp tip from a headlight lamp, cast away in the parties wire скобы and pull out a lamp for a socle from a reflector Insert a new lamp, connect it and then close a headlight.

Rotate a cap to the left and pull out it from the case. Raise then by means of a flat screw-driver a cartridge from the case and pull out a lamp from a cartridge. Insert a new lamp. Track correct landing of both directing ledges and close the case.



Should sit correctly: directing ledges.

Check of position of headlights – after each change of a lamp

As at replacement of a lamp of a headlight it is necessary to adjust a reflector before replacing a lamp, put the Mondeo whenever possible before a dark wall and mark with a chalk piece on a wall beams of light of serviceable lamps. After lamp replacement compare a light aperture of a new lamp to the old. If yours Mondeo it is obvious «mows aside» it is better to spend necessary юстировку light in a special workshop by means of the optical device for installation of headlights.

Cautiously raise a reflector of a headlight from forward дефлектора and... ... Then unscrew fixing screws of a lamp with the help крестовой шлицевой screw-drivers. Pull out now the case from an assembly aperture and disconnect the lamp tip. Pull out a lamp from a cartridge and insert a new lamp.



Installation in models with a serial bumper.

Open a cover of a luggage carrier and release a rotary clip of the corresponding case of a lamp. Remove a covering and... ... Separate the holder of a lamp from the case. For this purpose it is necessary to press both red plug-in uvulas (it is specified by an arrow).



Compress both red plug-in uvulas.

Disconnect now the lamp tip and pull out a defective lamp from a cartridge. After replacement instal upside-down. Do not forget to carry out the functioning control.



Унифицированно: back lanterns in models with an inclined and angular back of a body.

Open a back door and release in salon the top covering of the case of a lamp (the bottom is fixed by a gluing tape). Now remove a covering and... ... Unscrew both lambskin nuts of the case of a lamp. Take care of that nuts "have not failed" in apertures. Pull out the case outside, slightly compress a lamp in a cartridge and remove the left rotation. After replacement instal upside-down. Do not forget to carry out the functioning control.



Are mounted the friend over вругом: back lanterns in Mondeo Turnier

In models with a body a sedan simply displace a casing of the lamp holder. In models with a body of a compartment and the versatile person open in the beginning a back door. Then unscrew two screws with a crosswise head and remove a cap. After that disconnect the tip and pull out the holder of a lamp. For this purpose press both ledges. Replace a defective lamp and instal upside-down. Do not forget to check up functioning.



Additional lanterns of signals of braking: the complete set from five lamps.

Unscrew both screws with crosswise шлицем and pull out the case of a lamp from the buffer. Insert new софитную a lamp and instal upside-down.



Licence plate illumination: it is fixed by two screws with crosswise шлицем.

The next replacement of lamps накаливания

Any usual lamp накаливания is subject to deterioration: thread particles накаливания evaporate also it светоотдача decreases. Therefore in sector of external illumination (except галогенных lamps) replace lamps накаливания basically not less often, than in two years. "Growing old" lamps usually are distinguished visually on slightly turned black glass flask.