> Elimination of large scratches. Ford Mondeo (since 2000 of release)
Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
3.1. Internal clearing – at a dirt is not present any chances
3.2. An external sink
3.3. An engine sink
3.4. That all remains in movement, address in greasing service
3.5. Wish to keep material assets – look after colouring
3.6. Care of varnishing
3.7. Decrease in value of the goods – ugly defects of colouring
3.8. Elimination of defects from blows of stones
3.9. Polishing of small scratches
3.10. Elimination of large scratches
3.11. Installation for a sink of glasses
3.12. Check of a screen wiper and стеклоомывателя
3.13. Water pouring in стеклоомыватель
3.14. Replacement of rubber of a brush of a screen wiper
3.15. Nozzle installation стеклоомывателя
3.16. Installation and nozzle dismantle стеклоомывателя
3.17. Dismantle and installation of the lever of a screen wiper
3.18. Dismantle and installation of the electric motor of a forward screen wiper
3.19. Dismantle and installation of the electric motor of a back screen wiper
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
12. Brake system
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions
 






ba88fb63 Http hydraruzxpnew4af onion смотрите на http://0-hydra.net.

3-10-ustranenie-krupnykh-carapin.html

3.10. Elimination of large scratches

 PERFORMANCE ORDER

  1. In the presence of deep scratches on a bumper, wings or doors before repair it is better to dismantle these details of a body. The result will be better, if this work to execute manually.
  2. Grind places of damages by means of a grinding paper (granularity 80 or 100). In the presence of a rust polishing to spend before occurrence of naked metal. Then to put the converter of a rust and to allow to it to influence within nearby hour.
  3. In the beginning clean a place solvent for varnishes, degrease and well air.
  4. Mix шпаклевку and a hardener. Level шпаклевочную weight on height of a limiting surface of a place of defect.

     Attention: two-componental шпаклевка keeps, depending on temperature, the action within several minutes. Therefore make a mix of small volumes of both components.

  5. In regular intervals put шпаклевку and it is consecutive in some thin layers. Approximately in an hour шпаклевка will harden.
  6. Roughnesses eliminate a dry grinding paper (granularity 180). Definitive polishing spend with a humidified grinding paper (granularity 400). At surface polishing use a lot of water and put efforts.
  7. The remained flutes level now by means of шпаклевки. As soon as it will harden, grind all places a humidified grinding paper (granularity 600).
  8. Before colouring carefully смойте water all grinding dust.
  9. It is necessary to paste over thoroughly prepared places of damages now from different directions with a gluing tape, a film or old newspapers. Neglect certainly cheap gluing tape, it quickly размокает and is absorbed then a first coat.

    Attention: well air the workplace – during varnishing there are many harmful steams.

  10. Inject a first coat (наполнитель) as a basis for an integumentary varnish. Work purely – roughnesses and varnish ledges do not disappear after drawing of a painting layer but only increase. Let the first coat will dry out, then grind a humidified grinding paper (granularity 600). The polishing rests смойте water.
  11. In regular intervals put an integumentary varnish from an aerosol cylinder and it is continuous in some thin layers. The distance from a nozzle баллончика to a painted surface should make approximately 20–30 centimetres. Before colouring slightly warm up баллончик in hot water. Remove the rests of a paint then at a high pressure. Advantage: the surface becomes more smooth, and a varnish coat to more equal.
  12. Release edges of a gluing tape, turn in and sprinkle these places. Places of transitions to an existing varnish should be not so sharp and it is easier to polish them.
  13. As soon as the repair varnish completely will dry out (in the summer within nearby 2 days, in the winter in five days), process these places polish and places of transitions by a varnish cleaner. The best results are reached in the event that all car is in summary polished.
  1. When varnishing is carried out aerosol баллончиком, cut out in the big sheet of paper an aperture on the sizes of a place of damage. The varnish stream will cover a surface only in the set sizes.
  1. Scratches and scars should be eliminated grinding polish or a varnish cleaner if still there was a trace from an integumentary varnish. Use only the high-quality working material got in shops of spare parts.
  1. Wind a grinding paper round used grinding колодки, smoothly grind a damage place uniform circular motions in one direction. Колодку constantly moisten with water that the grinding dust was washed off.
  1. If you for the first time work with шпаклевкой, should be trained a little before beginning work. Spend training on an old detail from the car. It will give you necessary confidence and reliability at work with this material.
  1. Keep aerosol баллончик over a painted surface whenever possible in a quiet condition. Spend a stream on object of colouring, without a stop or oval movements is reduces formation degree потеков paints.

 PRACTICAL ADVICE

Special dust – an old paint, empty aerosol баллончики, dirty rags and brushes

The rests of a paint or dissolving means do not concern household dust, and to a special waste. It concerns also dirty rags, brushes and aerosol баллончиков. In many cities and settlements today there are mobile places of acceptance. Request in the department on protection of environment time of arrival of such stations or time of opening of specialised dumps.


The previous page
3.9. Polishing of small scratches
The following page
3.11. Installation for a sink of glasses