Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
3.1. Internal clearing – at a dirt is not present any chances
3.2. An external sink
3.3. An engine sink
3.4. That all remains in movement, address in greasing service
3.5. Wish to keep material assets – look after colouring
3.6. Care of varnishing
3.7. Decrease in value of the goods – ugly defects of colouring
3.8. Elimination of defects from blows of stones
3.9. Polishing of small scratches
3.10. Elimination of large scratches
3.11. Installation for a sink of glasses
3.12. Check of a screen wiper and стеклоомывателя
3.13. Water pouring in стеклоомыватель
3.14. Replacement of rubber of a brush of a screen wiper
3.15. Nozzle installation стеклоомывателя
3.16. Installation and nozzle dismantle стеклоомывателя
3.17. Dismantle and installation of the lever of a screen wiper
3.18. Dismantle and installation of the electric motor of a forward screen wiper
3.19. Dismantle and installation of the electric motor of a back screen wiper
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
12. Brake system
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions



3.6. Care of varnishing


    In the beginning it is necessary to wash out and dry the car thoroughly. In rather imperceptible places at first check up, whether colouring "will transfer" action полироля. Be cautious with a varnish cleaner: put its circular motions only thin layers. The thick layer of a cleaner "tears off" more than a superficial varnish, than it is necessary. Clean the Mondeo better for some passes. Put a polyrole or a cleaner polishing cotton wool (on the size of the fingers collected in a bunch) or a soft rag (but not from an artificial fibre) gentle effort circular motions. Process only visible surfaces.

    Divide a body into sites in the size about in half of square metre. If the size is more, polishing to carry out on it it is more difficult. Had time to dry up a polyrole to process much more difficultly.

    Already after a while actions the dry white deposit with which it is necessary to polish with a wadded tampon circular motions is formed. At strongly worn out varnish covering be cautious on edges: do not process the too long same place, it is possible even to tear off a paint to a first coat layer. Regularly overturn or replace a wadded tampon – its surface becomes covered after a while by particles of wax and means on leaving. To finish all rests полироля and threads from cotton wool, wipe polished лакировочную a surface a pure cotton rag.

    That the varnish seemed transparent and nonslipping, wipe to shine a white touch the big wadded tampon circular motions with small effort. If movements become inconvenient turn or replace a tampon.

    Put autowax by means of a wadded tampon. The size of a surface preserved for one working course depends on a used product. Attention: as a part of conservatives a high share of solvents. Therefore in the closed premises take care of presence of system of ventilation. Put preservative circular motions at weak effort by means of a cotton wool piece: uniform drawing increases depth of shine. Cotton wool should slide easily with small resistance on varnishing. Therefore overturn cotton wool more often and simultaneously for a stock take a new piece of cotton wool. If after that on a surface strips or stains more often they settle down on the covered colour particles – "heritage" of previous polish are still appreciable. Repeat process in slippery places.

    In end pound the polished surface in addition cotton rag. The possible rests of a touch thereby leave and it is natural a thread from cotton wool.

    If консерват at drawing almost flows down on varnishing, the superficial tension of a varnish is still great. Therefore try to put in this case before preservation soft a polyrole.

«The previous page
3.5. Wish to keep material assets – look after colouring
The following page»
3.7. Decrease in value of the goods – ugly defects of colouring