> Dismantle and installation of the lever of a screen wiper. Ford Mondeo (since 2000 of release)
Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
3.1. Internal clearing – at a dirt is not present any chances
3.2. An external sink
3.3. An engine sink
3.4. That all remains in movement, address in greasing service
3.5. Wish to keep material assets – look after colouring
3.6. Care of varnishing
3.7. Decrease in value of the goods – ugly defects of colouring
3.8. Elimination of defects from blows of stones
3.9. Polishing of small scratches
3.10. Elimination of large scratches
3.11. Installation for a sink of glasses
3.12. Check of a screen wiper and стеклоомывателя
3.13. Water pouring in стеклоомыватель
3.14. Replacement of rubber of a brush of a screen wiper
3.15. Nozzle installation стеклоомывателя
3.16. Installation and nozzle dismantle стеклоомывателя
3.17. Dismantle and installation of the lever of a screen wiper
3.18. Dismantle and installation of the electric motor of a forward screen wiper
3.19. Dismantle and installation of the electric motor of a back screen wiper
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
12. Brake system
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions
 






ba88fb63

3-17-demontazh-i-montazh-rychaga-stekloochistitelya.html

3.17. Dismantle and installation of the lever of a screen wiper

Forward screen wiper

 PERFORMANCE ORDER

  1. Mark a starting position of a parking of a brush of a screen wiper on glass by means of a gluing tape. Raise caps over an axis of the lever of a screen wiper by means of a small screw-driver and cast away up.
  2. Ослабьте a fixing nut approximately on two turns with the help накидного a key.
  3. Put the lever of a screen wiper and shake it sideways there-here – thereby it is released from a cone of an axis of a screen wiper. Strongly sitting levers should be wrung cautiously out by means of two шлицевых screw-drivers from a screen wiper axis. Not to damage colouring, enclose under fastening a rag.
  4. Cast away the lever, completely unscrew a nut.
  5. Disconnect the lever together with a lining washer from a shaft.
  6. At installation so level the screen wiper lever that it corresponded to the marks on glass. After installation check up a correctness of its course. Brushes should not be mixed with each other or to leave for a surface has flown down.

Back screen wiper

 PERFORMANCE ORDER

  1. Mark position of rest of a brush of a screen wiper on glass by means of a gluing tape.
  2. Cast away up caps and ослабьте a fixing nut approximately on two turns by means of a ring key.
  3. Put the lever of a screen wiper and – that it was released from a cone of an axis of a screen wiper – shake it sideways there-here and wring out. Strongly sitting lever cautiously wring out by means of two шлицевых screw-drivers from a screen wiper axis. Not to damage varnishing, enclose under fastening a rag.
  4. Cast away the lever, completely unscrew a nut.
  5. Disconnect the lever together with a lining washer from a shaft.
  6. At installation establish the screen wiper lever in the position marked on glass.

The previous page
3.16. Installation and nozzle dismantle стеклоомывателя
The following page
3.18. Dismantle and installation of the electric motor of a forward screen wiper