Ford Mondeo since 2000
1. Introduction
2. Equipment
3. Care of the car
4. Engines
5. Greasing system
6. Cooling system
7. System of injection of fuel
8. Ignition system
9. Fuel system
10. Transmission
11. A running gear
11.1. Forward bridge Mondeo
11.2. The service factor – geometry of the forward bridge
11.3. Check of shock-absorbers – is obligatory after deterioration of two complete sets of tyres
11.4. Regular check of a free wheeling of a steering wheel
11.5. Check of protective cuffs gear рейки
11.6. Check of tips of cross-section steering draught and cuffs
11.7. Check of the bearing of the cross-section lever of a suspension bracket
11.8. Check of a backlash of the wheel bearing
11.9. Replacement of the forward cross-section lever of a suspension bracket
11.10. Dismantle and installation of an amortisation rack
11.11. Replacement of tips of cross-section steering draught
11.12. Replacement of cuffs of the steering mechanism
11.13. Replacement of a rotary support of the steering mechanism
11.14. Dismantle and installation of a back amortisation rack
11.15. Replacement of the shock-absorber (versatile person)
11.16. The steering mechanism with the amplifier
11.17. Tyres and disks
11.18. It is better to check on cold tyres – pressure of air
11.19. Wheel replacement
11.20. Check of a condition of tyres
12. Brake system
13. The electrotechnical equipment
14. Electroschemes
15. Car salon
16. A body
17. Technical characteristics
18. The help at malfunctions
 



ba88fb63 Новосибирск проститутки вип



11-9-zamena-perednego-poperechnogo-rychaga-podveski.html

11.9. Replacement of the forward cross-section lever of a suspension bracket

In new Mondeo it is possible to replace the deformed cross-section lever only completely. It is better to transfer this work of a workshop (look section Check of the bearing of the cross-section lever of a suspension bracket). However if you count on yourselves it is possible for you to send a corresponding management. But all the same after carrying out of this work in any case it is necessary to spend gaugings and correction of the forward bridge in a special workshop.

 PERFORMANCE ORDER

    Establish a manual brake, ослабьте wheel nuts. Lift the car and reliably establish on goats. In addition fix the back bridge противооткатным an emphasis. Dismantle a forward wheel.

    Mondeo with the diesel engine
    Dismantle engine facing.

    Mondeo with gas-discharge headlights
    The left cross-section lever of a suspension bracket is connected to the gauge of a regulator of an angle of slope of an axis of headlights. In the beginning it is necessary to dismantle the gauge.

    All models
    Dismantle forward protection of a radiator from an auxiliary frame and... ... Lower an auxiliary frame on the corresponding party. Prop up the released frame an appropriate hydraulic jack. Further operate in a following order.

    Lower and prop up an auxiliary frame.

    Unscrew back screws of an auxiliary frame and fixing screws of the holder of an auxiliary frame. From an opposite side ослабьте screws on five turns. Unscrew forward fixing screws. Ослабьте opposite screws on five turns. Lower an auxiliary frame, now there is well accessible a screw of the cross-section lever of a suspension bracket. Not to damage bearings of the cross-section lever, it is necessary before weakening spherical hinge (it is specified by an arrow), is obligatory to lower an auxiliary frame. Separate both locations of bearings and dismantle the cross-section lever.

    Dismantle tightening the screw and a nut of the spherical hinge, remove a heat-shielding. Protect a rubber lining of the spherical hinge a soft rag.

    Dismantle of the cross-section lever of a suspension bracket

    Instal upside-down. Thus use new screws and nuts. Strongly and definitively tighten places of placing of bearings when you Mondeo again becomes wheels on the earth. Do not forget to mount a heat-shielding (fastening places are specified by arrows), level an auxiliary frame under forward wheels and then immediately fix.

    Installation of thermal protection.

    Spend a trial trip, then check up all screw connections and after that поезжайте in any case with the Mondeo on station of optical check of bridges and adjustment of geometry of the forward bridge.

The previous page
11.8. Check of a backlash of the wheel bearing
The following page
11.10. Dismantle and installation of an amortisation rack